Numeric Error Codes (2640-560 - 60x, 70x)

Numeric Error Codes
Symptom/Error    FRU/Action
10X 1. System Board
   101 Interrupt failure  
   102 Timer failure  
   103 Timer interrupt failure  
   104 Protected mode failure  
   105 Last 8042 command-  
   -not accepted  
   107 NMI test failure  
   108 Timer bus test failure  
   109 Low meg-chip select test  
110 1. Go to 'Memory Checkout'
  2. DIMM Card
  3. The computer is attached to the expansion unit
  4. System Board
111 1. Go to 'Memory Checkout'
  2. System Board
158 1. Set the password for hard disk drive
   (Hard disk password was not set  
   even thought the supervisor  
   password is set.)  
159 1. Set the correct password for hard disk drive
   (Hard disk password is not set  
   the same as the supervisor  
161 1. Go to 'Checking the Backup Battery'
   (Dead battery) 2. Backup Battery
  3. System Board
163 1. Reseat the keyboard connector
   (Time and Date was not set.)     on the system board
  2. Set Time and Date
  3. System Board
173 1. Reseat the keyboard connector
   (Configuration data were lost.)     on the system board
  2. Select OK in the error screen,
      then set time and date.
  3. Backup Battery
  4. System Board
174 1. Check Device Configuration.
   Configuration error (Perform 2. System Board
   'Checking the Installed Devices List' 3. Diskette Drive Assembly
   before changing any FRUs.) 4. Hard Disk Drive Assembly
175, 177, 178 1. System Board
   175: EEPROM CRC #1 error  
   177: Supervisor password  
   checksum error.  
   178: EEPROM is not functional  
183 1. Have the user examine the password
   (Incorrect password entered at  
   the supervisor password prompt.)  
184 1. Reset the POP in Easy-Setup.
   (POP check sum error.)  
185 1. Reset the startup sequence in Easy-Setup.
   (The startup sequence is not  
   valid. Suspect that power was off  
   when the startup sequence was  
   beeing updated.)  
186 1. System Board.
190 1. Go to 'Checking the Battery Pack'
   (A depleted battery pack was  
   installed when the power was on.)  
191XX 1. System Board
   (PM initialzation error)  
195 1. Check if the configuration
   (The configuration read from the     was changed
   hibernation area does not match     For example, check if the DIMM card
   the actual configuration.)     is added.
196 1. Run the hard disk drive test
   (Read error occured in the 2. Hard Disk Drive
   hibernation area of the HDD.)  
1XX 1. System Board
2XX 1. Go to 'Memory Checkout'
   201 Memory data error 2. DIMM Card
   202 Memory line error 00-15 3. System Board
   203 Memory line error 16-23  
   205 Memory test failure on  
   on-board memory  
   221 ROM to RAM remap error  
301, 303, 304, 305, 3XX 1. Go to 'Keyboard / Auxiliary Input Device Checkout'
   (Keyboard error) 2. Keyboard
  3. External Numeric Keypad
  4. External Keyboard
  5. Keyboard/Mouse Cable
  6. System Board
601, 6XX 1. Go to 'Diskette Drive Checkout'
   (Diskette drive or 2. Diskette Drive Assembly
   controller error.) 3. Diskette
  4. System Board
602 1. Go to 'Diskette Drive Checkout'
   (Diskette read error.) 2. Diskette
  3. Diskette Drive Assembly
604 1. Go to 'Diskette Drive Checkout'
   (Non-acceptable ID was read 2. Diskette Drive Assembly
   from the diskette drive.) 3. System Board
11XX 1. Serial Device (First)
   1101 Serial A test failure 2. Communication Cable
  3. System Board
12XX 1. System Board (Infrared)
   1101 Serial B test failure  
17XX 1. Hard Disk Drive
   1701 Hard sisk controller failure 2. System Board
   1780, 1790 Hard disk 0 error  
   1781, 1791 Hard disk 1 error  
24XX 1. System Board
   2401 System board video error  
808X 1. PCMCIA Slot Assembly
   8081 PCMCIA presence test failure 2. PCMCIA Device
   (PCMCIA revision also checked) 3. System Board
   8082 PCMCIA register test failure  
860X 1. External Mouse
   (Pointing device error when 2. External Keyboard
   TrackPoint III is disabled.) 3. System Board
   8601 Systembus error-  
   8042 mouse interface  
   8602 External mouse error  
   8603 System bus error or  
   mouse error  
861X 1. Reseat the keyboard cable on
   (Pointing device error when     the systemboard.
   TrackPoint III is enabled.) 2. Keyboard
   8611 System bus error-I/F between 3. External Mouse
   8042 and IPDC 4. System Board
   8612 TrackPoint error  
   8613 System board or TrackPoint error.  
I9990301 1. Check that the operating system.
   I9990302     is installed in the HDD.
   I9990305     If not, install the operating system.
   I9990301 Hard disk error 2. Reseat the boot device
   I9990302 Invalid hard disk boot 3. Check the startup sequence for the correct
   record.     boot device.
   I9990305 No bootable device 4. Check that the operating system has no
      failure and is installed correctly
I9990303 1. System Board
   Bank-2 flash ROM checksum error  
Other codes not listed above 1. Go to 'Undetermined Problems'

Please see the LEGAL  -  Trademark notice.
Feel free - send a Email-NOTE  for any BUG on this page found - Thank you.