- Turn the front door key to the 12 o'clock position to enable the robotics and the operator panel.
- Enter the initialization/setup mode by powering the tape library on or, if it is
already on, simultaneously pressing the MENU, CYCLE, SELECT control keys.
(After approximately six seconds the tape library starts the initialization routine.)
While the tape library is going through its initialization routine, rows 3 and 4 on the operator panel show:
PRESS a key to
Queue SETUP
-Attention- If you inadvertently enter the setup mode by pressing any one of the
control keys during library initialization, do not press the SELECT control key (right key) at any time, as this action will
alter the setup parameter currently shown on the operator panel.
To exit the setup mode without affecting any of the setup parameters, recycle the power (press the power switch off and then
on) or repeatedly press the MENU control key (left key) until you exit the setup mode.
- Press any one of the three control keys to enter the setup mode.
After the tape library finishes its initialization routine, rows 1 and 2 on the operator panel show:
SCSI ID = 6
Change to 7?
(This is a query to change the SCSI ID for the tape library controller.)
- To retain the current setting shown on row 1 and move on to the next parameter, press the MENU control key.
- To change the current setting to that shown on row 2 (that is, change SCSI ID 6 to 7) press the SELECT control key.
- If neither row 1 nor row 2 show the desired setting, change the display on row 2 by pressing the CYCLE key.
Press this key repeatedly to cycle through each of the alternatives (in the case of SCSI IDs, 0 through 7).
When row 2 shows the correct setting, press the SELECT key.
- After pressing the MENU or SELECT keys, rows 1 and 2 on the operator panel show:
SCSI PARITY ON
Change to OFF?
- To retain the current setting shown on row 1 and move on to the next parameter, press the MENU control key.
- To change the current setting to that shown on row 2 press the SELECT control key.
The next parameter and its current setting appear on row 1.
- After pressing the MENU or SELECT keys, rows 1 and 2 on the operator panel show:
INQUIRY=IBM XXX7
Change to YYY7?
Where XXX7 is the current machine type and YYY7 is the alternative machine type.
(Machine types are either 3447 or 7337.)
- To retain the current setting shown on row 1 and move on to the next parameter, press the MENU control key.
- To change the current setting to that shown on row 2 press the SELECT control key.
The next parameter and its current setting appear on row 1.
- After pressing the MENU or SELECT keys, rows 1 and 2 on the operator panel show:
3 of 9 CHECK ON
Change to OFF?
- To retain the current setting shown on row 1 and move on to the next parameter, press the MENU control key.
- To change the current setting to that shown on row 2 press the SELECT control key.
The next parameter and its current setting appear on row 1.
- After pressing the MENU or SELECT keys, rows 1 and 2 on the operator panel show:
AUTO INV-MC OFF
Change to ON?
- To retain the current setting shown on row 1 and move on to the next parameter, press the MENU control key.
- To change the current setting to that shown on row 2 press the SELECT control key.
The next parameter and its current setting appear on row 1.
- After pressing the MENU or SELECT keys, rows 1 and 2 on the operator panel show:
AUTO INV-Pwr OFF
Change to ON?
- To retain the current setting shown on row 1 and move on to the next parameter, press the MENU control key.
- To change the current setting to that shown on row 2 press the SELECT control key.
The next parameter and its current setting appear on row 1
- After pressing the MENU or SELECT keys, rows 1 and 2 on the operator panel show:
Scroll menu ON
Change to OFF?
- To retain the current setting shown on row 1 and move on to the next parameter, press the MENU control key.
- To change the current setting to that shown on row 2 press the SELECT control key.
The next parameter and its current setting appear on row 1.
- After pressing the MENU or SELECT keys, rows 1 and 2 on the operator panel show:
Autoloader OFF
Change to ON?
or, after pressing the MIDDLE key, rows 1 and 2 on the operator panel show:
Autoloader OFF
Change to LOOP?
- To retain the current setting shown on row 1 and move on to the next parameter, press the MENU control key.
- To change the current setting to that shown on row 2 press the SELECT control key.
- After pressing the MENU or SELECT keys, rows 1 and 2 on the operator panel show:
EXIT
Restart Setup ?
Note: If you inadvertently press the SELECT key during the setup procedure, you may alter your setup selections.
Therefore, before you exit setup, it is recommended that you quickly review and verify the setup
parameters that you have selected.
To review the parameters, press the SELECT key, then press the MENU (left) key repeatedly until you have
examined and verified each parameter.
When the operator panel displays the preceding screen, go to step 12.
- Press the MENU key to exit the setup procedure. The tape library is ready for normal operation.