AdapterId 05120h AdapterName "NCR IPSNet Board (IPSB or IEIB, ID 0x5120)" NumBytes 4 FIXEDRESOURCES pos[0]=00XXXXX1b pos[1]=00000XXXb pos[2]=XXXXXXXXb pos[3]=100XXXXXb NamedItem Prompt "IPSNet Board Interrupt Mapping for INT 1 Input" choice "IRQ LEVEL 9" pos[2]=XXXXXX11b INT 9 choice "IRQ LEVEL 7" pos[2]=XXXXXX10b INT 7 choice "IRQ LEVEL 5" pos[2]=XXXXXX01b INT 5 choice "IRQ LEVEL 3" pos[2]=XXXXXX00b INT 3 Help "Set the lnterrupt level so it will not conflict with other interrupting devices. Diskettes are usually level 6." NamedItem Prompt "IPSNet Board Interrupt Mapping for INT 2 Input" choice "IRQ LEVEL 9" pos[2]=XXXX11XXb INT 9 choice "IRQ LEVEL 7" pos[2]=XXXX10XXb INT 7 choice "IRQ LEVEL 5" pos[2]=XXXX01XXb INT 5 choice "IRQ LEVEL 3" pos[2]=XXXX00XXb INT 3 Help "Set the interrupt level so it will not conflict with other interrupting devices. Diskettes are usually level 6." NamedItem Prompt "IPSNet Board Interrupt Mapping for INT 3 Input" choice "IRQ LEVEL 9" pos[2]=XX11XXXXb INT 9 choice "IRQ LEVEL 7" pos[2]=XX10XXXXb INT 7 choice "IRQ LEVEL 5" pos[2]=XX01XXXXb INT 5 choice "IRQ LEVEL 3" pos[2]=XX00XXXXb INT 3 Help "Set the interrupt level so it will not conflict with other interrupting devices. Diskettes are usually level 6." NamedItem Prompt "IPSNet Board Interrupt Mapping for INT 4 Input" choice "IRQ LEVEL 9" pos[2]=11XXXXXXb INT 9 choice "IRQ LEVEL 7" pos[2]=10XXXXXXb INT 7 choice "IRQ LEVEL 5" pos[2]=01XXXXXXb INT 5 choice "IRQ LEVEL 3" pos[2]=00XXXXXXb INT 3 Help "Set the interrupt level so it will not conflict with other interrupting devices. Diskettes are usually level 6." NamedItem Prompt "BURST synchronization Enable" choice "Enable" pos[0]=XX1XXXXXb choice "Disable" pos[0]=XX0XXXXXb Help "If this bit is set to Disable the board circuitry will generate a synchronized BURST pulse. When this bit is set to Enable, the 94C18A Interface Chip will generate this synchronized pulse." NamedItem Prompt "I/O Address Select" choice "400" pos[1]=XXXXX001b io 00400h-0043Fh choice "3240" pos[1]=XXXXX010b io 03240h-0327Fh choice "4240" pos[1]=XXXXX011b io 04240h-0427Fh choice "5240" pos[1]=XXXXX100b io 05240h-0527Fh choice "6240" pos[1]=XXXXX101b io 06240h-0627Fh choice "8240" pos[1]=XXXXX110b io 08240h-0827Fh choice "A240" pos[1]=XXXXX111b io 0A240h-0A27Fh Help "This is the I/O Port of the IPSNet Board. Conflicting assignments are marked with an asterisk and must be changed to use the host adapter." NamedItem Prompt "DMA Fairness Technique" choice "Fairness Enabled" pos[3]=XXX1XXXXb choice "Fairness Disabled" pos[3]=XXX0XXXXb Help "If 'Fairness' is enabled, the NCR IPSNet Board will not compete for the channel during the next arbitration phase if it is currently in control of the channel. This allows other installed boards to obtain the channel in the next sequence based on each board's assigned priority level. When 'Fairness' is disabled, the board will compete for every arbitration phase and will obtain more than its fair share of channel usage. We recommend you use 'Fairness Enabled' for all boards." NamedItem Prompt "DMA Channel 1 Level Select" choice "DMA Level 3" pos[0]=XXX0011Xb arb 3 choice "DMA Level 0" pos[0]=XXX0000Xb arb 0 choice "DMA Level 1" pos[0]=XXX0001Xb arb 1 choice "DMA Level 5" pos[0]=XXX0101Xb arb 5 choice "DMA Level 6" pos[0]=XXX0110Xb arb 6 choice "DMA Level 7" pos[0]=XXX0111Xb arb 7 Help "The NCR IPSNet Board supports the direct memory access (DMA) mode of data transfer. Each DMA level has a corresponding priority level; the lower the DMA level, the higher the corresponding priority. You may select any one of the DMA levels listed. We recommend you select the first level listed, DMA level 3. If your selection conflicts with a DMA level already assigned in the system, it will be marked with an asterisk and you must select an alternative level." NamedItem Prompt "DMA Channel 2 Level Select" choice "DMA Level 7" pos[3]=XXXX0111b arb 7 choice "DMA Level 0" pos[3]=XXXX0000b arb 0 choice "DMA Level 1" pos[3]=XXXX0001b arb 1 choice "DMA Level 5" pos[3]=XXXX0101b arb 5 choice "DMA Level 6" pos[3]=XXXX0110b arb 6 choice "DMA Level 3" pos[3]=XXXX0011b arb 3 Help "The NCR IPSNet Board supports the direct memory access (DMA) mode of data transfer. Each DMA level has a corresponding priority level; the lower the DMA level, the higher the corresponding priority. You may select any one of the DMA levels listed. We recommend you select the first level listed, DMA level 7. If your selection conflicts with a DMA level already assigned in the system, it will be marked with an asterisk and you must select an alternative level."