Adaptec AHA-2940/2940W/2944W PCI-to-Fast SCSI Host Adapter

Adaptec AHA-2940/2940W/2944W PCI-to-Fast SCSI Host Adapter.


see >> SCSI 68-Pin Internal and External Connector
see >> SCSI Interface - Electrical Specifications



FRU P/N 06H5250 Adaptec AHA-2940 SCSI-2 PCI Adapter

OPT P/N VSCPCI1


FRU P/N 06H6431 Adaptec AHA-2940W SCSI-2 F/W PCI Adapter


FRU P/N 07H0132 Adaptec AHA-2940S SCSI-2 Fast PCI Busmaster Adapter


FRU P/N 12J3094 Adaptec AHA-2940UW SCSI - PCI F/W Ultra Adapter

OPT P/N 76H5407 Adaptec AHA-2940UW SCSI - PCI F/W Ultra Adapter (76H3579)



Use only single-ended SCSI devices with the AHA-2940/2940W. Use only differential SCSI devices with the AHA-2944W. Devices may be damaged if used with the wrong SCSI specification. Read the SCSI device documentation if you are not sure whether the device is single-ended or differential.

Only two of the three connectors on the AHA-2940W/2944W host adapter can be used at the same time.
Resistor Network (RN) setup for AHA-2944W Adapter

Low High Install Remove
Off Off None All RNs
On On RN1, RN2, RN9, RN10, RN11 and RN12
with 10-pin 330-ohm RNs
RN3, RN4, RN5, RN6, RN7 and RN8
with 10-pin 150-ohm isolated RNs
None
Off On RN9 and RN12 with 330-ohm bussed RNs
RN3 and RN6 with 150-ohm isolated RNs
RN1, RN2, RN4
RN5, RN7, RN8
RN10 and RN11


RN1 RN2 RN9 RN10 RN11 and RN12 are 330-ohm resistor networks
RN3 RN4 RN5 RN6 RN7 and RN8 are 150-ohm resistor networks
A 330-ohm resistor will have a 330 or 331 included in the part number printed on the resistor and a 150-ohm resistor will have 150 or 151.
Jumper Table

AHA-2940 AHA-2940W AHA-2944W Description
J1 J3 J1 50-Pin 8-Bit Internal SCSI Connector
J2 J1 J2 External LED Connector
J3     50-Pin 8-Bit External SCSI Connector
  J2 J3 68-Pin 16-Bit Wide Internal SCSI Connector
J4 J4 J4 Termination Jumper for Multiple Computer Configurations
  J6 J6 68-Pin 16-Bit Wide External SCSI Connector
U4 U5 U21 AIC-7870 PCI-SCSI Bus Master Chip
U5 U6 U23 Host Adapter BIOS ROM


 


If there is installed a jumper shunt on the J4 termination jumper on the AHA-2940/2940W host adapter, it is possible to create a configuration in which SCSI devices can be shared between two computers without changing the cable configuration every time one or the other computer needs to access the devices. (The two computers and the SCSI peripherals are all connected on one SCSI bus.) Only one computer can be turned on at any one time, and that computer will acts as a terminator at one end of the SCSI bus.

Restrictions 


Contents of the AHA-2940 Adapter Kit:

3x 1.44 Diskettes
3x Users Guide Books

AHA-2940/2940W/2944W Features
PCI Bus Interface 

Fast Data Transfer Rates 
AHA-2940
AHA-2940W/2944W
Maximum Off-loading the Host CPU 

Fully Disk Array Capable 

Fast SCSI-2 Implementation 

Multiple Device and Application Support 

 ADAPTEC EZ-SCSI 3.03L
 The following information is available in this section:

    1.  Upgrade Information
    2.  New Features
    3.  CD-ROM Drive Support
    4.  Scanner Support
    5.  Floptical Support
    6.  SETUP Command Line Options
    7.  ASPIBUF.SYS
    8.  SMARTDRV 5.0 and XA formatted CDs
    9.  ASPI8DOS.SYS Information
   10.  Troubleshooting/Limitations


 1.  Upgrade Information
 If you are using a custom version of Adaptec EZ-SCSI which may not include the
 following components: SCSI Tape Backup utility, Photo CD Viewer, Microsoft
 CD-ROM extensions (MSCDEX).
 To upgrade to the standard version of Adaptec EZ-SCSI for $29, call Adaptec
 at one of the following numbers:
 Adaptec Phone Numbers 

 Technical Support                               (800) 959-7274
 M-Th: 6:00am to 5:00pm, F: 6:00am to 3:00pm
 Pacific Standard Time
 Bulletin Board Service (BBS)                    (408) 945-7727
 24 hours a day (up to 14400 baud, using
 8 bits, 1 stop bit, no parity)
 Literature Hotline                              (800) 934-2766
 M-F: 5:00am to 6:00PM Pacific Standard Time
 Software Ordering (U.S.A. and Canada)           (800) 442-7274
 M-F: 5:00am to 6:00pm Pacific Standard Time
 International Software Ordering                 (818) 365-6264
 M-F: 5:00am to 6:00pm Pacific Standard Time
 Interactive Fax Service                         (408) 957-7150
 24 hours a day

 2.  New Features
 Adaptec EZ-SCSI 3.03L features numerous enhancements including:
 o  Easy to use Windows installation utility
 o  Additional CD-ROM support (including LUN/jukebox support)
 o  HP scanner support
 o  1024 bytes / sector support added to ASPIDISK.SYS and AFDISK.EXE
 o  Windows based SCSI tutorial
 o  Windows on-line catalog of 3rd party companies
 o  Windows on-line description of EZ-SCSI files
 o  Music database feature added to our Windows CD Play utilities
 o  Floptical support added to ASPIDISK.SYS
 o  Volume serial ID support added to ASPIDISK.SYS for removable media
 o  AHA-1520/1522/1520A/1522A configuration utility (Windows)
 o  Wide SCSI support added to ASPIDISK.SYS and AFDISK.EXE (for users of
    the AHA-2740W/2742W and the AHA-2940W/2944W)
 o  Removable media lock/unlock/eject utility, RMVTOOL.EXE (DOS command
    line utility)
 o  VASPID.386 has been rewritten to allow TimerCriticalSection=xxxx to be
    specified in your SYSTEM.INI
 o  ASPIBUF.SYS added (see below)
 o  * PCI host adapter support
 o  ** AHA-1530P/1532P "Plug and Play" support
 *  New to Adaptec EZ-SCSI 3.01
 ** New to Adaptec EZ-SCSI 3.02
 The following Adaptec SCSI Host Adapters are fully supported:
 ISA Bus 
 o  Adaptec AVA-1505
 o  Adaptec AVA-1515
 o  Adaptec AHA-1510/1520/1522
 o  Adaptec AHA-1510A/1520A/1522A
 o  Adaptec AHA-1530P/1532P
 o  Adaptec AIC-6260 or AIC-6360 based SCSI host adapters
 o  Adaptec AHA-1540B/1542B
 o  Adaptec AHA-1540C/1542C
 o  Adaptec AHA-1540CF/1542CF
 Microchannel Bus 
 o  Adaptec AHA-1640
 EISA Bus 
 o  Adaptec AHA-1740/1742/1744
 o  Adaptec AHA-1740A/1742A
 o  Adaptec AHA-2740/2742/2740T/2742T
 o  Adaptec AHA-2740A/2742A/2740AT/2742AT
 o  Adaptec AHA-2740W/2742W
 o  Adaptec AIC-7770 based SCSI host adapters
 VL Bus 
 o  Adaptec AVA-2820/2822/2825
 o  Adaptec AHA-2840VL/2842VL
 PCI Bus 
 o  Adaptec AHA-2940
 o  Adaptec AHA-2940W
 o  Adaptec AHA-2944W
 o  Adaptec AIC-7870 based SCSI host adapters
 3.  CD-ROM Drive Support
 The following drives have been tested by Adaptec with Adaptec
 EZ-SCSI 3.03.  All drives support both audio and data.  Photo CD is
 supported where indicated:

                                      Firm-
 Name            Model                ware    SCSI    Photo CD
 ----            -----                -----   ----    --------
 Compaq          CDU561-31            1.8I    2       multi session
                 CDU6611-31           1.8B    2       multi session
 Chinon        * CDS 431              H48     1       single session
                 CDS 435              M62     1       single session
                 CDS 535              Q08     2       multi session
 Denon         * DRD 253              V       1       single session
 Hitachi         CDR 1750S            12      1       single session
                 CDR 3750             4       1       single session
                 CDR 6750             0005    2       multi session
                 CDR 1950S            0005    2       multi session
 IBM             Internal CD-ROM      2443    2       multi session
                 Enhanced CD-ROM II   0893    2       multi session
 LMS (Philips) * CM 214               .12     1       single session
                 CM 215               .13     2       multi session
 NEC             CDR 38               1       2       multi session
              ** CDR 55JD             1       1       multi session
               * CDR 72               E       1       single session
                 CDR 73               1.2     1       single session
               * CDR 74               1       1       single session
                 CDR 74               1.0a    1       single session
                 CDR 74-1             1       2       multi session
               * CDR 84               1       1       single session
                 CDR 84               1.0a    1       single session
                 CDR 84-1             1       2       multi session
              ** CDR 210              1.0     1       multi session
                 CDR 210P             1.0     1       multi session
                 MultiSpin 3X         1.0     2       multi session
                 CDR 500              1.0     2       multi session
                 CDR 510              1.0     2       multi session
                 MultiSpin 4X         2.5A    2       multi session
                 CDR 900              2.5A    2       multi session
 Panasonic/      501 family           1.0B/C  1       single session
 Matsushita      CR 503               1.0A    2       multi session
                 CR 532               2.0A    2       multi session
                 CR 532               2.5A    2       single session
                 CR 533               1.1a    2       multi session
                 LK-MC501S            1       1       single session
 Philips CDD-BK01 / IMS CCD-463       0.00    2       multi session
 Pioneer     *** DRM 600              806     1       single session
             *** DRM 604X             2403    2       multi session
 Plextor/Texel   Shinaken 3021        1.04    1       single session
                 Shinaken 5021        1.04    1       single session
                 DM 5021              1.04    1       single session
                 DM 3024              1.10    2       multi session
                 DM 5024              1.10    2       multi session
                 DM 3028              3.00    2       multi session
                 DM 5028              3.00    2       multi session
 Sanyo           CRD 400E             1.31    2       multi session
                 CRD 400I             1.31    2       multi session
 Sony            CDU 541-01           2.6A    1       single session
                 CDU 561              1.8K    2       multi session
                 CDU 561-31           1.8i    2       multi session
                 CDU 6211-10          2.6A    1       single session
 TEAC            CD 50                1       2       multi session
 Toshiba         XM 3101BME           3232    1       no
                 TXM 3201A1           3332    1       single session
                 XM 3301B             272     2       single session
                 XM 3401B             283     2       multi session
                 TM 3301E             2162    2       multi session
                 TX 3401B             2       2       multi session
                 XM 4101B             2893    2       multi session
 *    These drives do not directly support Photo CD.  However, by adding
      /XAEMUL to the ASPICD.SYS command line, in your CONFIG.SYS, we will
      emulate support for single session Photo CD on these drives.
 **   These drives do not support parity.  Please consult the troubleshooting
      section of the users manual for information on using these drives.
 ***  These jukebox CD-ROM drives are fully supported.  A drive letter will
      be assigned for each CD.

 4.  Scanner Support
 Hewlett-Packard's driver for HP ScanJet II scanners is included with Adaptec
 EZ-SCSI.  This driver is named SJIIX.SYS and is designed to function with
 Adaptec's ASPI managers.
 Installation of the driver is easy.  Simply run Adaptec EZ-SCSI.  Adaptec
 EZ-SCSI automatically detects your HP scanner and installs SJIIX.SYS into
 the appropriate section of your CONFIG.SYS file.  You can then install
 HP's DESKSCAN software if it is not already installed.
 SJIIX.SYS supports the following applications using TWAIN or the
 application's scanning utility:
 Aldus: PhotoStyler
 Arkenstone: Arkenstone Reader II
 Caere: FaxMaster, OmniPage Direct, OmniPage Professional, PageKeeper
 Calera: TrueScan, WordScan, WordScan Plus
 Corel: Corel Draw
 Delrina: WinFax, WinFax Pro
 Eclipse systems: Eclipse fax
 ExperVision: TypeReader
 Image-In: Image-In
 Intel® : Satisfaction
 Light Source: Ofoto
 Micrografx: Picture Publisher
 Pixel Translations: Open Book
 RIX Software: WinRix
 Westbrook: File Magic
 WordStar/ZSoft: Publisher's Paintbrush, PhotoFinish
 5.  Floptical Support
 ASPIDISK.SYS has been modified to support Insite and IOMega floptical
 drives.  For those of you already familiar with ASPIDISK.SYS and AFDISK.EXE,
 using floptical drives is a bit different.  Do NOT use AFDISK.EXE to
 format media inserted in your floptical drive.  You can use SCSIFMT.EXE
 to low-level format the media if necessary.  To do a DOS format of your
 media, simply insert the media into the floptical drive and run the DOS
 FORMAT utility (run EZ-SCSI first).
 6.  SETUP Command Line Options
 There are a couple of command line options that are available with the
 Windows version of EZ-SCSI (SETUP.EXE):

 Option:        noctl3d
 Example:       c:\setup noctl3d
 Description:   EZ-SCSI for Windows uses a Dynamic Link Library (DLL) called
                CTL3D.DLL that gives its dialog boxes the 3-D gray-box look.
                This command line options disables the loading of this DLL.
                Note that EZ-SCSI defaults to not loading this DLL if you are
                using Central Point's Desktop (e.g. PC Tools for Windows 1.0).
 Option:        noscan
 Example:       c:\setup noscan
 Description:   By default, EZ-SCSI will automatically scan your hardware for
                SCSI host adapters and SCSI devices. In the unlikely event
                that this fails, we've provided an override switch that
                instructs EZ-SCSI to NOT scan for hardware. It will simply
                decompress the files on to your hard disk. You would then
                need to manually edit your CONFIG.SYS and/or AUTOEXEC.BAT.

 7.  ASPIBUF.SYS
 The ISA bus is limited to 24 bits of address. 2^24 = 16 MBytes.  What does
 this mean?  It means that an ISA card that uses DMA cannot physically
 access memory beyond 16 MBytes of RAM. This is a limitation of the ISA
 bus.
 The 16 MByte issue is not a limitation with PCI cards, EISA cards, VL cards,
 or PIO cards.  It is only an issue with an ISA card that uses DMA such as
 the AHA-1540/1542. ASPIBUF.SYS is an ASPI double-buffering driver that
 you load immediately after ASPI4DOS.SYS (e.g. before ASPICD.SYS, ASPIDISK.SYS,
 etc.).  It, along with ASPI4DOS.SYS, must both be loaded low before EMM386
 (or QEMM, 386MAX, etc.). It intercepts ASPI and INT 13h commands and double-
 buffers both so that these data transfers occur within the first 16 MBytes
 of RAM.  ASPIBUF.SYS is intelligent enough to not double-buffer if the
 ASPI or INT 13h buffer is already within the first 16 MBytes of RAM.  It is
 only designed to work with ASPIDISK.SYS, ASPICD.SYS, and INT 13h commands.
 Other ASPI drivers and/or applications may or may not work.  ASPI FOR
 WINDOWS APPLICATIONS (E.G. SHOWSCSI.EXE) will BE DISABLED ONCE THIS DRIVER
 IS LOADED.
 By default, ASPIBUF.SYS will allocate a 16K buffer for double-buffering.  You
 can specify the size (2K-64K) by using the size= command line switch.  For
 example:

 device=c:\scsi\aspi4dos.sys /d
 device=c:\scsi\aspibuf.sys /size=8
 device=c:\scsi\aspidisk.sys /d

 8.  SMARTDRV 5.0 and XA formatted CDs
 SMARTDRV 5.0 (in MS-DOS 6.2, Windows for Workgroups 3.11) now includes
 caching for CD-ROM drives.  There is a problem with SMARTDRV in its support
 for XA formatted Compact Discs.  If you experience "Not Ready" errors,
 using SMARTDRV 5.0, add /E:2048 to your SMARTDRV command line.  For example:

 C:\DOS\SMARTDRV /X /E:2048

 9.  ASPI8DOS.SYS Information
 The driver ASPI8DOS.SYS was added after the user's manual went to print.
 For information on the available command line switches, refer to the
 ASPI7DOS.SYS section in the user's manual.  ASPI8DOS.SYS uses the same
 switches that ASPI7DOS.SYS does.  ASPI8DOS.SYS supports the following PCI
 SCSI host adapters:

 Adaptec AHA-2940
 Adaptec AHA-2940W
 Adaptec AIC-7870 based SCSI host adapters

 10.  Troubleshooting/Limitations

 o  If you have an Adaptec PCI SCSI host adapter installed in the system,
    and EZ-SCSI for DOS does not detect the host adapter, try running
    EZ-SCSI with the /pci command line switch.  For example:
    a: <Enter>
    ezscsi /pci <Enter>
    Note that if the system has EMM386.EXE loaded, from MS-DOS versions up
    to 6.2, the system might hang when using the /pci switch.  This has been
    fixed in MS-DOS 6.21 and later.  If you experience this problem, you
    should not load EMM386.EXE when running EZ-SCSI for DOS.  The same applies
    to SCSIFMT.EXE.  EZ-SCSI for Windows does not exhibit this problem and
    should find the Adaptec PCI SCSI Host Adapter regardless of the PCI
    system and whether or not you have EMM386.EXE loaded.
    ASPI8DOS.SYS can be loaded high.  However, due to the EMM386.EXE problem
    mentioned above, some PCI systems will hang if loading ASPI8DOS.SYS after
    EMM386.EXE.  If you experience this problem, you will either need to load
    ASPI8DOS.SYS before EMM386.EXE, or upgrade to MS-DOS 6.21 or later.  Other
    ASPI modules (e.g. ASPICD.SYS) can continue to be loaded high.
 o  EZ-SCSI for Windows (SETUP.EXE) will not load it's 3-D look DLL (CTL3D.DLL)
    if you are using Central Point PC Tools for Windows Desktop.  The
    installation will still proceed without any loss of functionality.
 o  You should install Adaptec EZ-SCSI to a drive letter that exists at boot
    time.  This would NOT include RAM drives, network drives, removable
    drives, etc.
 o  In the unlikely event that you encounter a timeout failure when EZ-SCSI
    for Windows scans the SCSI bus, you should run EZ-SCSI for DOS first.
    Let it modify your CONFIG.SYS to load the appropriate ASPI managers;
    Reboot your system.  You should then be able to run EZ-SCSI for Windows.
 o  If you have an  AHA-2740W/2742W or an AHA-2940W (Wide SCSI Host
    Adapter), the SCSI Interrogator for Windows (SHOWSCSI.EXE) will only
    show icons for SCSI IDs 0-7.  You will not see IDs 8-15.

 Adaptec 7800 Family Manager V1.02 for OS/2 2.X
 (Supports AHA-2940 and AIC-78xx)
 Installation instructions for the AIC-7870 OS/2 2.x driver: 
 Installing the driver on a system containing OS/2 2.x
 1) Open the OS/2 System Folder, then open the System Setup folder.
 2) Double-click on Device Driver Install.
 3) Insert the Manager Set floppy in the appropriate drive.
 4) Change to the directory where the driver is located, usually OS2\2_X.
 5) When you find the driver (AIC7870.ADD), select INSTALL.
 6) After the install finishes, a message will appear to report the
    status.  An error will be displayed if no host adapters are found.
 NOTE:
    If you are using OS/2 2.0 GA, the above method will not work.
    To install under 2.0 GA, open a full-screen OS/2 session.  Change to
    the drive and directory on the floppy where the drivers are located.
    Type DDINSTAL and press ENTER.
    You may also install the driver manually.  Copy AIC7870.ADD to C:\OS2.
    Add a line to your CONFIG.SYS that says BASEDEV=AIC7870.ADD .
    Intel® Errata #8511 lists known data integrity issues with the
    processor cache on the Saturn-1 chipset (82424TX).  For this reason
    Adaptec recommends that processor cache be disabled via the CMOS
    setup to avoid data corruption.  For more information, see Intel®
    Errata #8511.  You may get this from Intel® FaxBack system at
    800.628.2283 or 916.356.3105.  For more detailed information see
    Errata #8512 and 8513.
 Installing OS/2 2.1 and higher from floppy diskette 
 1) Make backup copies of the Installation Diskette and Disk #1.
 2) Using the backup copies of the Installation Diskette and Disk #1
    do the following:
    a) Copy OS2LDR from the 7800 Manager Set onto the Installation Diskette.
    b) Copy IBMINT13.I13 from the 7800 Manager Set onto Disk #1.
 3) Install OS/2 using the backup diskettes and the remainder
    of the standard OS/2 diskettes.
 4) When installation has completed, Reboot the system.
 5) After the system has Rebooted, follow the instructions for installing
    the driver on a system containing OS/2.
 ***** IMPORTANT *****
 There is currently no support for installing OS/2 2.0 on a hard disk
 attached to an AIC-7870, due to limitations in the installation procedure.
 Upgrading to OS/2 2.1 or higher is recommended.
 Installing OS/2 2.x from CD-ROM 
 1) Make a backup copy of Disk #1.
 2) Copy the file AIC7870.ADD to the backup copy of Disk #1.
 3) Using a text editor, add the following line to the CONFIG.SYS found
    on Disk #1 :
         BASEDEV=AIC7870.ADD
 4) When installation has completed, Reboot the system.
 General Installation Notes 
 OS/2 2.x currently does not identify PCI systems and handles them
 in the same way it would an ISA system. This can cause several different
 problems: trouble installing OS/2 2.x and an inability to share a single
 interrupt between multiple PCI adapters.
 IBM is aware of these problems and has open APARs (PJ14230 and PJ14710)
 tracking them. They will be fixed in a future release of OS/2; please check
 the list of closed APARs accompanying each future release.
 Currently, we have files which can be used as interim fixes for both these
 problems:
 OS2LDR - A new PCI aware version of the loader. This file can be used during
 installation or installed after the installation of OS/2 has completed.
 IBMINT13.I13 - A new PCI aware version of the generic INT 13H driver that
 is used during installation from floppy disk.
 If you update Disk #1 of the CD-ROM installation to include OS2LDR, please be
 aware that this file will be overwritten from the CD-ROM. It may have to be
 updated again on the boot drive when the installation has completed.
 Configuration: 
 Generic command line switches for Adaptec drivers and OS/2 2.X 
 OS/2 adapter device drivers (.ADD files) are normally installed
 automatically and require no further information from the user. However,
 in certain situations the user may wish to modify the behavior of the
 driver to meet their specific needs.
 ***** IMPORTANT *****
 Please proceed cautiously with the following information. If you have
 purchased software which requires you to use switches, it should include
 instructions on how to use them. Most software requires no switches and
 you do not need to concern yourself with the information about switch
 settings.
 The standard format for command line switches is :
 BASEDEV=AIC7870.ADD [Universal Parameter][Adapter ID][Unit Parameter]
           {[SCSI Target ID]}
   [Universal Parameter] - An option that applies to all adapters
            controlled by the driver.
   [Adapter ID] - /A:n, where n is the number (zero relative) of the adapter
            installed in the system. The adapter ID is determined when
            the driver is loaded based on the order that adapters are
            found in the system. (See below, AIC7870.ADD Specific Command
            Line Switches.)
   [Unit Parameter] - Modifies the behavior of the selected host adapter.
   [SCSI Target ID] - The targets to which the Unit Parameter will be applied.
            This parameter may be a single ID (d) or list of IDs (d,d,d).
 Universal Parameters 
    /ET - Allow embedded targets.  This parameter indicates that the ADD
       should assume that all targets have more than one logical unit (LUN)
       defined.
    /!ET - Do not allow embedded targets (DEFAULT). This parameter indicates
       that the ADD should assume that all targets have only one logical
       unit (LUN) defined.
    /V - Load driver verbosely. This parameter will display the driver
       name as well as the version number and Adaptec copyright if the driver
       loads successfully. Information on all targets found in the system
       will also be displayed.
 General Unit Parameters 
    /I - Ignore the specified adapter. This allows another driver to
       share the adapters that the ADD would normally use.
    /DM - Enable DASD manager support (DEFAULT). This parameter allows
       OS2DASD.DMD to control the specified target(s) if they are
       identified as DASD (hard disk) devices.
    /!DM - Disable DASD manager support. This parameter prevents
       OS2DASD.DMD from controlling the specified target(s).
    /SM - Enable SCSI manager support (DEFAULT). This parameter allows
       OS2SCSI.DMD to control the specified target(s) if they are
       identified as NON-DASD SCSI devices. All SCSI hard disk
       will be controlled by OS2DASD.DMD.
    /!SM - Disable SCSI manager support. This parameter prevents
       OS2SCSI.DMD from controlling the specified target(s).
 Configuration Examples 
 Example 1
    Suppose that you had a removable hard disk as target 3 and you wanted
    to control the hard disk with an ASPI application and driver.
    Normally OS2DASD will allocate this device, treat it as a large
    floppy and prevent you from sending any SCSI commands via ASPI.
    BASEDEV=AIC7870.ADD /A:0 /!DM:3 will prevent OS2DASD.DMD from
    accessing the target and still allow OS2SCSI.DMD and OS2ASPI.DMD to
    share access to it.
 Example 2
    Suppose that you had a multi-disk CD-ROM as target 4 on host adapter 0 and
    two DASD devices as targets 1 and 5 on host adapter 1.
    BASEDEV=AIC7870.ADD /ET /A:0 /!SM:4 /A:1 /!DM:1,5 will prevent
    OS2SCSI.DMD from accessing the CD-ROM and prevent OS2DASD.DMD from
    controlling the DASD devices. The driver will also search for multiple
    LUNs on all host adapters.
 Important Tips
   1) There are no switches for controlling OS2ASPI.DMD directly. IBM did
     not define them in their specification and we cannot be sure that other
     host adapters will have the same switches.
   2) OS2SCSI.DMD will only allocate devices when a device driver
     requests it, but this will prevent OS2ASPI from accessing it. There is
     nothing in the ASPI specification regarding device allocation so
     OS2ASPI must rely on other managers to fairly share targets. This
     should only be a problem if you have two drivers that use different
     managers and you want them both to access the same target at the same
     time.
   3) Do NOT disable DASD manager access to target 0 if you are booting
     from your SCSI host adapter. This will prevent the system from booting!
 AIC7870.ADD-specific command line switches 
 This driver supports the AIC-7870 installed on an AHA-2940 PCI host
 adapter.  Adapter numbers are first assigned to boards with their BIOS
 enabled; the numbers are assigned from lowest BIOS address to highest
 address.  Any remaining boards are assigned numbers by scanning slots.
 Each slot is a combination of a bus number and a device number pair
 starting from lowest to highest numbers, and the adapters are assigned a
 number in the order they are found.
 Special Unit Parameters: 
       /TAG: - Sets the number (1-16) of tagged commands for all target
               devices on the host adapter. A value of one disables
               tagged queuing. 16 is the maximum number allowed and 8 is
               the default value.
       /TAG:1  Disables tagged queuing for all target devices on a given
               host adapter. The driver maintains a maximum of 2 non -
               tagged commands per target internally. The driver treats
               all target devices as non tagged devices, and sends only
               one command at a time per target to the host adapter.
        Example:
        BASEDEV=AIC7870.ADD /A:0 /TAG:8
                will set the number of tagged commands for all target
                devices on the first host adapter to 8.
 Limitations: 
      Due to an OS problem, OS/2 cannot currently support more than one
      AHA-2940 (AIC7870) host adapter board.  IBM is working to
      fix this.  Contact IBM for the status of this problem (APAR PJ14230).
      Fault Tolerance is now supported in the driver. However, ABORT and
      SCSI BUS RESET will only work for targets that are properly
      behaved.
 Adaptec 7800 Family Manager Set v1.02 - Windows NT
 Driver v1.01 release for Windows NT v3.1
 Directory Structure: 
 The files on this diskette which are required for the installation of
 the 7800 series Windows NT driver are as follows:
     \DISK1               - Disk tag file
     \TXTSETUP.OEM        - Install script used during NT installation
     \WINNT\AIC78XX.SYS   - Adaptec 7800 series driver v1.01 for Windows NT
     \WINNT\README.TXT    - This file
     \WINNT\OEMSETUP.INF  - Install script used by Windows NT Setup
 Installation instructions for the AIC-7870 WIN/NT driver: 
 Read this to find out about 
    Adding, swapping, and removing Adaptec 7800 Family host adapters
    in computers running Microsoft Windows NT
    Installing Windows NT with an Adaptec 7800 Family host adapter(s)
    Using software parameters to change the configuration of Microsoft
    Windows NT drivers
 Installation and Product Overview 
 The Adaptec 7800 Family driver, aic78xx.sys, allows the Windows NT
 operating system to recognize the Adaptec AHA-2940/2940W, single-chip
 AIC-7870, and single-chip AIC-7850 host adapters. These host adapters
 are referred to collectively as the Adaptec 7800 Family host adapters.
 At the time of this writing, the Windows NT drivers are supplied by
 Adaptec only. In the future, however, Windows NT will supply Adaptec
 drivers to function with the Adaptec 7800 Family of host adapters.
 Adaptec always ships the latest Windows NT driver in the 7800 Family
 Manager Set. This driver enables the Adaptec 7800 Family host adapters
 to perform at an even higher level under Windows NT. The procedures in
 this readme explain how to install Windows NT with the latest Adaptec
 driver.
 Requirements 
    A PCI computer, with an installed and configured Adaptec AHA-
    2940/2940W host adapter(s); or a PCI computer with an embedded AIC-
    7850 or AIC-7870 single-chip host adapter.
    An installed primary (boot) floppy diskette drive. A 3.5-inch
    (1.44 MByte) or 5.25-inch (1.2 MByte) high-density floppy
    diskette drive is required.
    An installed and configured CD-ROM drive (optional) for installing
    from the compact disc. See your computer and peripheral documentation
    for details.
    The Windows NT distribution software and documentation.
    The Adaptec 7800 Family Manager Set Diskette for NetWare, OS/2,
    and Windows NT.
    The Adaptec AHA-2940/2940W User's Guide.
 Performing a Windows NT Installation 
 Follow these instructions if you are installing an Adaptec AHA-
 2940/2940W host adapter and Windows NT at the same time. You may install
 Windows NT from a floppy drive or from a CD-ROM drive; whichever you
 choose, make sure the hardware installation is completed prior to following
 these steps.
 If you know that Adaptec drivers are supplied with your Windows NT
 version, follow these procedures exactly to install the new driver. The
 install program tries to access the old driver on other Windows NT
 floppy disks or from the CD during installation.
    1  If you choose to install Windows NT from a floppy drive, locate
       the Windows NT Disk 1 for Floppy Installation. Make a backup
       copy of this diskette.
 If you are installing from a CD-ROM drive, locate the Windows NT Setup
 Disk for CD-ROM Installation. Make a backup copy of this diskette.
    2  Delete the file aic78xx.sys on the backup diskette you just
       created. This file may not be on the disk; if it is not, skip this
       step.
    3  Put the backup diskette into drive A (not drive B) and turn
       on your computer.
    4  When prompted, select Custom setup.
 Caution: If you choose Express setup, the installation process is unable
 to detect your Adaptec host adapter and the installation fails.
    5  Windows NT setup cannot recognize the adapter and displays
       none. Press S to configure additional SCSI adapters.
    6  From the list of additional SCSI adapters, select Other
       (Requires disk provided by a hardware manufacturer).
    7  Insert the Adaptec 7800 Family Manager Set Diskette for
       NetWare, OS/2, and Windows NT into drive A and press Enter.
    8  The screen displays the adapter similar to Adaptec Driver
       for AIC78xx SCSI Controller. Press Enter.
    9  If you want to add other host adapters (that are not a part
       of the 7800 Family), do so at this time by following steps 6 through
       8 for each additional adapter. The 7800 Family of host adapters
       uses the same driver, so this step is not necessary for them.
    10 Press Enter to continue with the Windows NT operating system
       setup. Follow the instructions given onscreen and in the Windows NT
       Installation documentation.
 Updating Windows NT with the New Driver 
 This section explains how to make the following hardware changes to your
 computer without reinstalling Windows NT:
    Add an Adaptec host adapter that uses the same driver as one
    already installed in your computer, and add an Adaptec host adapter
    that uses a different driver
    Swap an Adaptec host adapter for one that uses a different driver
    Remove an Adaptec host adapter
 NOTE: These operations are similar but have important distinctions, as
 described in the following sections. Read the instructions carefully
 before you change your computer configuration.
 Adding a Host Adapter 
 This section details installing a host adapter in a computer. If you are
 adding an Adaptec host adapter to a computer that already has an
 installed host adapter of the same family (for example, if you have
 added an AHA-2940 to a computer that already has an installed AHA-2940),
 perform steps 1 through 5 only.
 If you are adding a host adapter that uses a different driver, you must
 perform all the steps in this section to ensure that the device driver
 for the new host adapter is both installed on your system disk and is
 enabled.
 The steps are as follows:
    1  Shut down Windows NT if your computer is ON.
    2  Power OFF your computer and physically install the new host
       adapter in an available slot. Refer to the host adapter hardware
       documentation for installation.

   Always refer to your computer's documentation for instructions
 on opening the computer cover and adding boards.
    3  Verify that there are no system resource conflicts (e.g.
       interrupt request level or DMA channel) between the new host adapter
       and other hardware installed in the computer. Refer to the host
       adapter hardware documentation for instructions; changes may be
       necessary to the CMOS Setup.
 NOTE: Depending on the BIOS for the PCI system, this step may not be
 necessary.
    4  Restart the computer.
    5  Boot Windows NT. If you have just added an Adaptec host
       adapter to a computer that already has an installed host adapter of
       the same family (for example, if you have added an AHA-2940 to a
       computer that already has an installed AHA-2940), your installation
       is complete, do not perform steps 6 through 15.
    6  Select and start the Windows NT Setup program. (Its icon is
       usually found in the Main program group.) There is a brief pause while
       Windows NT Setup scans your hardware -configuration.
    7  Select the Options pull-down menu and then select Add/Remove
       SCSI Adapters. The SCSI Adapter setup program displays a list of the
       types of host adapters currently installed.
    8  Click on the Add button to add another host adapter type to
       the list. Expand the list and select the type of host adapter to be
       added. For this example, we assume you are adding an AHA-2940 to a
       computer that already has an AHA-1540C.
    9  Click on the Install button.
 At this point, Windows NT Setup checks to see if the specified driver
 (in this example, aic78xx.sys) has already been copied to the system
 disk. If this type of host adapter was previously installed, the
 following message appears:
 The driver(s) for this SCSI adapter are already on the system
    10 Click on Current if you want to use the existing device
       driver or click on New if you want to replace it. If you select
       Current, skip to step 12.
 If the device driver has never been installed, this message appears:
 Please enter the full path to the Windows NT SCSI Adapter files.
    11 Change the path to the directory with the desired device
       driver, then click on Continue.
 The device driver is copied to your system disk and the
 Windows NT configuration is updated so that the new device driver loads
 when Windows NT Reboots.
    12 When the installation is complete, Windows NT Setup again
       displays a list of currently installed host adapter types. Verify
       that the new host adapter appears on the list; the string should
       look similar to:
    Adaptec Driver for AIC78xx SCSI Controller
    13 Add other types of host adapters if necessary (see steps 8
       through 12 above), or click on Close to exit the SCSI adapters
       portion of Windows NT Setup, and then close the program.
    14  When you see this message, click on OK to exit:
 The changes you have made will not take effect until the computer is
 restarted
 If this message does not appear, no changes have been made to the
 Windows NT system configuration.
    15 Restart your computer and Windows NT. It is possible that
       some drive letter assignments may change from the previous
       configuration.
 Swapping a Host Adapter 
 Swapping one type of host adapter for another is similar to the
 procedure for adding a host adapter. The important distinction is that
 you make all software configuration changes while Windows NT is running
 and before you make the hardware changes.
    1  Install the driver for the new host adapter by following
       steps 6 through 15 in the section Adding a Host Adapter on page 3-5.
 It is not essential to remove the device driver for the host adapter you
 are replacing. Windows NT dynamically detects the absence or presence of
 host adapter hardware, and no problems should arise if you leave the
 existing device driver installed. You may remove the device driver
 later, after you have successfully Rebooted Windows NT. However, if you
 leave the driver in, the system alerts you with an error message of the
 extra device driver every time you boot.
    2  Once the new device driver is installed, shut down Windows
       NT and replace the existing host adapter, as described in steps 1
       through 5 of Adding a Host Adapter on page 3-5.
    3  Restart your computer and Windows NT. It is possible that
       some drive letter assignments may change from the previous
       configuration.
 Caution: If the host adapter you are swapping controls the computer boot
 device, you must follow the additional steps in the next section in
 order for Windows NT to work correctly.
 Swapping the Boot Host Adapter 
 If the host adapter you are swapping controls the system disk from which
 your Windows NT loads, you must update the device driver in two locations
 (because Windows NT boots in a two-stage process): the Windows NT device
 driver directory (i.e. \winnt\system32\drivers) and c:\ntbootdd.sys.
 In the first stage of booting, no software configuration is available
 and Windows NT loads the device driver to control the computer boot disk
 from the file c:\ntbootdd.sys. Therefore, when you perform the steps
 described above to swap a host adapter you must also explicitly copy the
 aic78xx.sys device driver to c:\ntbootdd.sys (meaning that aic78xx.sys
 is copied over and renamed as c:\ntbootdd.sys).
 NOTE: The c:\ntbootdd.sys file is system, hidden, and read only; you
 must use an attribute change program to disable the hidden and read only
 attributes. For example, using DOS, enter attrib -h -r -s c:\ntbootdd.sys
 to disable the these attributes before c:\ntbootdd.sys can be modified.
 ntbootdd.sys is always located on your C drive, even if the system disk
 once Windows NT boots is a different disk. For example MS-DOS is
 installed on your IDE disk C, and Windows NT is installed on SCSI disk D.
 Removing a Host Adapter 
 Removing a host adapter can be as simple as physically removing it from
 the slot when your computer is shut down. Windows NT boots and functions
 properly in this configuration, but a warning message is generated every
 time you boot Windows NT.
 Caution: If you have removed a host adapter but still have other host
 adapters of the same type installed in your computer, do not use Windows
 NT Setup to remove the device driver.
 To eliminate the warning message, you must update the Windows NT
 software configuration, as described in these steps:
    1  Select and start the Windows NT Setup program. (Its icon is
       usually found in the Main program group.) There is a brief pause
       while Windows NT Setup scans your hardware -configuration.
    2  Select the Options pull-down menu and select Add/Remove SCSI
       Adapters. The SCSI Adapter setup program displays a list of the
       types of host adapters currently installed.
    3  Select the type of host adapter you want to remove and click
       on the Remove button. When the Windows NT Setup program asks you for
       confirmation, click on OK.
 Because SCSI device drivers are loaded during system bootup and because
 they may be needed to load Windows NT itself, the following warning
 message appears:
 The SCSI adapter has been marked as a boot device. Removing it may cause
 the system not to boot.
    4  If you are sure you are removing the correct host adapter
       type, click on OK.
    5  Return to step 3 if you want to remove driver support for
       other types of host adapters, or click on Close to exit the SCSI
       adapters portion of Windows NT Setup.
    6  Close the Windows NT Setup program. When the following
       message appears click on OK to exit:
 The changes you have made will not take effect until the computer is
 restarted.
 If this message does not appear, no changes have been made to the
 Windows NT system configuration.
    7  Restart your computer. Note that Windows NT Setup does not
       delete the device driver from your system disk; it only updates
       Windows NT software configuration information so that the device
       driver is no longer loaded during system bootup.
 Updating a Device Driver 
 If a software update is available for a particular host adapter device
 driver, you may update your Windows NT system without any hardware or
 software configuration changes by following these steps:
    1  Copy the new device driver to the directory -
       Xxxxx\System32\Drivers, where Xxxxx is the system root of Windows NT
       (typically named \winnt).
    2  If you are updating the device driver that controls the
       computer boot device, copy the same driver to the file
       c:\ntbootdd.sys.
 NOTE: The c:\ntbootdd.sys file is system, hidden, and read only; you
 must use an attribute change program to disable the hidden and read only
 attributes. For example, using DOS, enter attrib -h -r -s
 c:\ntbootdd.sys to disable the these attributes before c:\ntbootdd.sys
 can be modified.
    3  Shut down and restart your computer.
 Troubleshooting 
 The boot manager for Windows NT contains recovery logic to allow you to
 return to the last known good configuration. If you have changed your
 host adapter configuration and Windows NT no longer boots, follow these
 steps to recover:
    1  Undo any hardware changes you have made to the computer
       since it was last operational.
    2  Reboot the computer. Watch the display carefully during
       bootup. If the following message appears, press the Spacebar and
       follow the instructions on the screen to continue booting with
       the last known good configuration:
 Press spacebar NOW to invoke the Last Known Good menu
    3  Once your computer is operational again, double check all of
       the hardware and software configuration changes you want to make.
       Look specifically for conflicts with parts of the existing system
       configuration that are not being changed.
 If you cannot determine the source of the error, contact Adaptec.
 Adaptec 7800 Family Managers for NetWare 3.1X and 4.0X - V1.02
 This capture contains Adaptec's Novell solution for the AIC-7800 Family of
 Host Adapters. This includes AHA-2940s (PCI to SCSI), all AHA-2740Ws (PCI
 to SCSI with wide channel), AIC-7870 (Chip on the motherboard supporting wide
 channel), AIC-7850 (Chip on the motherboard supporting 8 bit SCSI channel).
 The files included on the diskette which are required for the installation
 of the NetWare drivers are as follows:
        \netware\v3_1x\aic7870.dsk
        \netware\v3_1x\aspitran.dsk
        \netware\v4_0x\aic7870.dsk
        \netware\v4_0x\aic7870.ddi
        \netware\v4_0x\aspitran.dsk
 If required, please consult your DOS manual on how to move around the
 directory tree.
 Within a subdirectory, you will find a README.TXT file describing the
 driver(s) contained in that subdirectory.
 The disk provides the following NetWare drivers:
 1.) AIC-7870 Family of Host Adapters Driver For NetWare 386 v3.11 and v3.12.
           (\netware\v3_1x)
 2.) AIC-7870 Family of Host Adapters Driver For NetWare 386 v4.00 and v4.01.
           (\netware\v4_0x)
 3.)  ASPITRAN.DSK ASPI Transport Layer Manager Driver for NetWare v3.1x.
            (\netware\v3_1x)
 4.)  ASPITRAN.DSK ASPI Transport Layer Manager Driver for NetWare v4.0x.
             (\netware\v4_0x)
 5.)  AIC7870.DDI Driver definition information file for NetWare v4.0x only.
             (\netware\v4_0x)


Coosing SCSI Cables for AHA-2940 Ultra / AHA-2940 UltraWide

SCSI Device Type AHA-2940 Ultra AHA-2940 UltraWide
8-bit Internal SCSI 50-pin internal
SCSI cable
50-pin internal
SCSI cable
8-bit External SCSI 50-pin high density
external SCSI cable
-
16-bit Internal
Wide SCSI
- 68-pin internal
SCSI cable
16-bit External
Wide SCSI
- 68-pin external
SCSI cable


Terminating the AHA-2940 Ultra Wide Adapter

Termination of the AHA-2940UW itself is controlled by software commands via the SCSISelect utility. The default setting is set to Automatic.

It is recommended to leave the AHA-2940UW set to its default setting of AUTOMATIC. The following table lists the termination settings for manual configuration.

Devices Connected to AHA-2940UW AHA-2940 Ultra
Wide Termination
Low ---- High
68-pin internal connector only ON ----- ON
68-pin external connector only ON ----- ON
68-pin internal and 68-pin external connectors Off ---- Off
50-pin internal connector only ON ----- ON
50-pin and 68-pin internal connectors OFF ---- ON
50-pin and 68-pin external connectors OFF ---- ON


Back to  Jump to TOP-of-PAGE

Please see the LEGAL  -  Trademark notice.
Feel free - send a Email-NOTE  for any BUG on this page found - Thank you.