IntelliStation - 6889, 6897 Models

IntelliStation - 6889, 6897 (dual) Pentium® II - 350 - 500 MHz Models

  See Asset EEPROM backup - before start, replacing System Board.

1 Secondary microprocessor socket (U25)

See > Second Microprocessor - Installation

2 Primary microprocessor socket (U24)
3 Power connector (J5M1)
4 Secondary microprocessor fan sink connector (J4)
5 Power connector (J2M1)
6 Primary microprocessor fan sink connector (J3)
7 DIMM connectors (DIMM 0,1,2,3)
8 SCSI channel-B 16-bit connector (J10D1)
9 Power switch and LED connector (J11B1)
10 Hard disk LED connector (J11B1)
11 Diskette drive connector (J8F2)
12 Primary IDE connector (J9F1)
13 RFID antenna connector (J15)
14 SCSI channel-B 8-bit connector (J10E1)
15 Secondary IDE connector (J8F1)
16 Battery
17 Internal speaker connector (J12B13)
18 Clear CMOS jumper (J7E1)
19 Fan connector, frontpanel (J5)
20 Fan connector, frontpanel (J6)
21 Tamper detect switch connector (J12B1)
22 Switches (SW12A1)
23 Wake On LAN connector (J6D1)
24 Wake On Modem connector (J13)
25 SCSI channel-A connector (J10F1)
26 RAID port extension (J4D1)
27 Shared ISA/PCI connectors
28 PCI slot connectors
29 AGP slot connector (J2E3)
30 CD audio connector (J1F1)
31 Microphone connector
32 Audio line In/Out connector
33 RJ-45 Ethernet connector
34 JTAG (J4F1)
35 Rear panel fan connector (J7)
36 Parallel/Serial-1/Serial-2 connectors
37 USB-1/USB-2 connectors
38 Keyboard/Mouse connectors

The following tables contain switchand jumper setting information. (D) indicates the default setting.

Processor Speed Switch Setting (SW1 1-4)

Speed	SW1-1	SW1-2	SW1-3	SW1-4
350 MHz	Off	Off	ON	ON
400 MHz	ON	ON	Off	ON
450 MHz	Off	On	Off	On

Note: Pentium® III Processors do not require speed settings. For Pentium® III Processors you can ignore the speed settings.

Normal ROM Operation Switch (SW1 5)

ROM Operation	SW1-5
Normal	Off (D)
ROM Recovery Mode	On

Enet Normal Operation Switch (SW1 6)

Enet Operation	SW1-6
Normal	Off (D)
Enet Disabled	On

Admin Password Lock Switch (SW1 7)

Admin Password	SW1-7
Locked	Off (D)
Unlocked	On

Diskette Operation Switch (SW1 8)

Diskette Operation	SW1-8
Normally	Off (D)
Read Only	On

Clear CMOS Request Jumper Setting (J7E1)

Jumper	Setting	Description
J7E1	1-2(D)	Normal Operation
J7E1	2-3	Erase Password Configuration (Clear CMOS)

  See > System Board Memory
for DIMM size, speed, and type.

DIMM sizes of 32, 64, 128, and 256 MB are acceptable. Use 100MHz, SDRAM DIMMs.
Do not mix Registered and Non-Registered DIMMs. When installing or removing memory, any sequence of DIMM size is allowed.
Fill each DIMM connector sequentially, starting at DIMM socket 0. If SDRAM ECC and SDRAM (non-parity) DIMMs are mixed, they will configure as non-parity ECC.
Install only SDRAM ECC DIMMs to enable ECC.

Please see the LEGAL  -  Trademark notice.
Feel free - send a   for any BUG on this page found - Thank you.