Post Error Codes and Messages List - Aptiva (SL-A) 2139/53/58/63

POST Error Codes and Messages List

NOTE: To diagnose a problem, first find the BIOS error messages or codes in left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause.

BIOS Error Codes, Messages	Action/FRU
0111	ISA adapter card
I/O Parity Error	System board
0127	Check CPU speed and system board DIP switches.
CPU Clock Mismatch
	See 'System Board Jumpers and Connectors'
	for 'Machine Type 2139'
	for 'Machine Type 2153/K6'
	for 'Machine Type 2153/Celeron™'
---	for 'Machine Type 2158'
	for 'Machine Type 2163'.
	System board
0151	Enter BIOS Setup and load the default settings.
Real Time Clock Error	CMOS battery.
0161	System board.
CMOS Battery Bad
0162
CMOS Checksum Error
0162	Ensure the system configuration set in BIOS Setup is correct.
Equipment Configuration Error	See 'BIOS Setup Utility'
	Enter BIOS Setup and load the default settings.
	CMOS battery.
	System board.
0163	Ensure the time set in BIOS Setup is correct.
Date and Time Incorrect	See 'Date and Time'
	CMOS battery.
0164	Insert the memory modules in the DIMM sockets properly,
Memory Size Change	then reboot the system.
0201	Memory module.
Memory Error at MMMM:SSSS:OOOOh	See the 'Step 005 of 'Memory' to replace memory module.
	System board.
301	Re-connect PS/2 keyboard and mouse.
PS/2 Keyboard Error or	Enter BIOS Setup and load the default settings.
Keyboard Not Connected	PS/2 keyboard
303	PS/2 mouse
PS/2 Keyboard Interface Error	System board
0662
Onboard Floppy Drive I/O Address
Conflict(s)
0662
Onboard Floppy Drive DMA Conflict(s)
0662
Onboard Floppy Drive IRQ Conflict(s)	Enter BIOS Setup and load the default settings.
	Remove all adapter cards that are NOT factory-installed,
	then reboot the system.
0662	Diskette drive cable/connection.
Floppy Disk Controller Error	Diskette drive.
0662	System board
Floppy Drive A Error
0662
Floppy Drive B Error
0648	Ensure that the diskette drive is not set to [Write Protected]
Floppy Drive(s) Write Protected	in the Security Options in BIOS Setup.
	Load default settings in Setup.
0962	Enter BIOS Setup and load the default settings.
Onboard Parallel Port	Remove all adapter cards that are NOT factory-installed,
Conflict(s)	then reboot the system.
0962
Onboard Parallel Port I/O
Address Conflict(s)
0962
Onboard Parallel Port
IRQ Conflict(s)
0962
Onboard ECP Parallel Port
DMA Conflict(s)
1162
Onboard Serial Port
Conflict(s)
1162
Onboard Serial Port I/O
Address Conflict(s)
1162
Onboard Serial Port IRQ Conflict(s)
1755	Ensure that the hard disk drive is not set
Hard Disk Drive(s) Write Protected	to [Write Protected] in the
	Security Options in BIOS Setup.
	Load default settings in Setup.
1762	Enter BIOS Setup and load the default settings.
Onboard IDE Primary Channel I/O	Remove all adapter cards that are NOT factory-installed,
Address Conflict(s)	then reboot the system.
1762
Onboard IDE Primary Channel IRQ
Conflict(s)
1762
Onboard IDE Secondary Channel I/O
Address Conflict(s)
1762
Onboard IDE Secondary Channel IRQ
Conflict(s)
1780	Enter BIOS Setup and load the default settings.
IDE Primary Channel Master Drive Error	Check IDE drive jumper.
1781	See '3.5-In. Hard Disk Drive Jumper Settings' and
IDE Primary Channel Slave Drive Error	'5.25-In. Hard Disk Drive Jumper Settings'.
1782	IDE hard disk drive power.
IDE Secondary Channel Master Drive Error	IDE hard disk drive cable/connection.
1783	IDE hard disk drive.
IDE Secondary Channel Slave Drive Error
1780	Enter BIOS Setup and load the default settings.
IDE Primary Channel Master Drive	IDE hard disk drive cable/connection.
Changed
1781
IDE Primary Channel Slave Drive
Changed
1782
IDE Secondary Channel Master Drive
Changed
1783
IDE Secondary Channel Slave Drive
Changed
1800	Load default settings in Setup.
IRQ Setting (PnP ISA Card(s) disabled)	Enter BIOS Setup and set the Reset Resource
1801	Assignments parameter to Yes, then
Expansion ROM Allocation Failed	reboot the system. See 'PnP/PCI Options'.
1802	Remove all adapter cards that are NOT factory-installed,
I/O Resource Conflict(s)	then reboot the system
1803
Memory Resource Conflict(s)
1800	Do not have enough system resource allowed to
PnP ISA Card(s) Disabled	allocate for ISA adapter card.
	Remove the ISA adapter card.
	Load default settings in Setup.
	Enter BIOS Setup and set the
	Reset Resource Assignments parameter to Yes,
	then reboot the system.
	See 'PnP/PCI Options'.
	Remove all adapter cards that are NOT
	factory-installed, then reboot the system
8601	PS/2 Pointing Device Error or Not Connected
PS/2 Pointing Device Interface Error	Re-connect PS/2 keyboard and mouse.
8603	Enter BIOS Setup and load the default settings.
PS/2 Pointing Device Error	PS/2 mouse
8603	PS/2 keyboard
	System board
8602	Enter BIOS Setup and load the default settings.
Onboard Pointing IRQ Device Conflict(s)	Remove all adapter cards that are NOT
	factory-installed, then reboot the system.