General Checkout (Type 6265,6267,6275,6277,6285,6287,6561,6591,6862,6889,6892,6893,6897)


This General Checkout procedure is for Type 6265, 6267, 6275, 6277, 6285, 6287, 6561, 6591, 6862, 6889, 6892, 6893, 6897 computers.


NOTE: See Universal Management Agent (UMA) for UMA information and the computer types that support UMA.

  The drives in the computer you are servicing might have been rearranged or the drive startup sequence changed. Be extremely careful during write operations such as copying, saving, or formatting. Data or programs can be overwritten if you select an incorrect drive.


Diagnostic error messages appear when a test program finds a problem with a hardware option.
For the test programs to properly determine if a test Passed, Failed,  or Aborted , the test program check the error-return code at test completion. See 'Return Codes'.


General error messsages appear if a problem or conflict is found by an application program, the operating system, or both. For an explanation of these messages, refer to the information supplied with that software package.

NOTE:

  1.  Before replacing any FRUs, ensure the latest level of BIOS is installed on the system. A down-level BIOS  might cause false errors and unnecessary replacement of the system board.  For more information on how to determine and obtain the latest BIOS, see 'BIOS Levels'.
  2.  If multiple error codes are displayed, diagnose the first error code displayed.
  3.  If the computer hangs with a POST error, go to 'Symptom-to-FRU Index'.
  4.  If the computer hangs and no error is displayed, go to 'Undetermined Problem'.
  5.  If an installed device is not recognized by the diagnostics program, that device might be defective.


The power-on default is quick bring-up. To enable Enhanced bring-up, select the Start Options in the Configuration/Setup Utility program (see 'Setup Utility Program') then, enable Power On Status

 +---+
 |001|
 +---+
 - Power-off the computer and all external devices.
 - Check all cables and power cords.
 - Make sure the system board is seated properly.

 - Make sure the processor speed setting matches the processor installed in the computer.

 - Set all display controls to the middle position.
 - Insert the IBM PC Enhanced Diagnostics diskette into drive A.
 - Power-on all external devices.
 - Power-on the computer.
 - Check for the following response:
   1. Readable instructions or the Main Menu.
      NOTE: Type 6263, 6265, 6267, 6275, 6277, 6285, 6287, 6561, 6591,
            6862, 6865, 6872, 6889, 6892, 6893, 6897 computers are default to
            come up quiet (No beep and no memory count and checkpoint code display)
            when no errors are detected by POST.
            To enable Beep and memory count and checkpoint code display when a successful POST occurs:
             1. Enable Power on Status in setup. See 'Setup Utility Program'.
 DID YOU RECEIVE THE CORRECT RESPONSE ?
            +---+
  Yes    No-+002| If the Power Management feature is enabled, do the following:
   |        +---+
   |              1. Start the 'Configuration/Setup Utility' program
   |              2. Select Power Management from the Configuration/Setup Utility program menu.
   |              3. Select APM
   |              4. Be sure APM BIOS Mode is set to Disabled
   |                 if it is not, press Left Arrow (<) or Right Arrow (>) to change
   |                 the setting.
   |              5. Select Automatic Hardware Power Management
   |              6. Set Automatic Hardware Power Management to Disabled
   |                 - or -
 +-+-+               Go to the 'Symptom-to-FRU Index'
 |003|
 +---+
 Run the IBM PC Enhanced Diagnostic test. If necessary, refer to 'Diagnostics and Test Information'.
  ° If you receive an error, replace the part that the diagnostic program calls out
    or go to 'Symptom-to-FRU Index'
  ° If the test stops and you cannot continue, replace the last device tested.
  ° If the computer has incorrect keyboard responses, go to 'Keyboard'
  ° If the printer has incorrect responses, go to 'Printer'
  ° If the dsplay has problems such as jittering, rolling, shifting, or being out of focus,
    go to 'Display'


Back to  Jump to TOP-of-PAGE

Please see the LEGAL  -  Trademark notice.
Feel free - send a Email-NOTE  for any BUG on this page found - Thank you.