NetFinity 3500 - Type 8644 - Pentium® II Models
NetFinity 3500 - Type 8644 - Pentium® II Models
See > System Board Replacement - BIOS UPDATE procedure
See > System Hangs/No Video
See > 333MHz Processor Upgrade
1 CD-ROM audio connector MPC3 (J1F1)
2 Fan connector, rear panel (J1M1)
3 3.3V, 5V power auxiliary connector
4 Primary microprocessor socket (Klamath)
5 Power connector
6 Secondary microprocessor socket (Klamath)
7 DIMM connectors (MEM 3-2-1-0)
8 CMOS clear jumper (J7E1)
Jumper 1-2 = Normal Operation (D)
Jumper 2-3 = Erase Password and Configuration
9 Power switch and power/Hard disk LED connector (J9L1)
10 Secondary IDE connector
11 Diskette drive connector
12 Primary IDE connector
13 Channel A SCSI connector (68-pin)
14 Channel B SCSI connector (50-pin)
15 Channel B SCSI connector (68-pin)
If you install wide (16-bit) SCSI devices,
you can set the IDs to any whole number
between 0 and 6, or between 8 and 15.
If you install narrow (8-bit) SCSI devices,
you can set the IDs to any whole number
between 0 and 6.
16 Reserved (J4F1)
17 SCSI LED connector (4-pin) (J11B1)
18 Internal speaker connector (J12B3)
19 Tamper detect switch connector (J12B1)
20 Fan connector, front (upper) panel (J12B2)
21 Fan connector, front (lower) panel (J12A1)
22 Switch set (SW1)
23 Battery
24 SCSI LED (2-pin) connector (J10A1)
25 Wake On LAN connector (J6D1)
26 Wake On Modem connector (J9A1)
27 RAIDport extensions
(The RAIDport connector is not supported)
28 ISA slot connectors
29 External SMBus connector (J0B1)
30 PCI slot connectors
31 AGP slot connector
32 Secondary microprocessor fansink connector (J3F2)
33 Primary microprocessor fansink connector (J2E1)
34 Microphone connector
35 Audio line In/Out
36 RJ-45 Ethernet connector
37 Parallel/Serial 1 - Serial 2 connectors
38 USB 1 - USB 2 connectors
39 Keyboard/Mouse connectors
Processor Speed Switch Setting (SW1 1-4)
| Speed |
SW1-1 |
SW1-2 |
SW1-3 |
SW1-4 |
| 233 MHz |
Off |
Off |
ON |
ON |
| 266 MHz |
ON |
ON |
Off |
ON |
| 300 MHz |
Off |
ON |
Off |
ON |
| 333 MHz |
ON |
Off |
Off |
ON |
ROM Operation Switch (SW1-5)
| ROM Operation |
SW1-5 |
| Normal Operation |
Off (D) |
| ROM Recovery Mode |
ON |
Ethernet Operation Switch (SW1-6)
| ENET Operation |
SW1-6 |
| Normal Operation |
Off (D) |
| Enet MAC Disabled |
ON |
Admin Password Lock Switch (SW1-7)
| Admin Password |
SW1-7 |
| Locked |
Off (D) |
| Unlocked |
ON |
Diskette Operation Switch (SW1-8)
| Diskette Operation |
SW1-8 |
| Normal Opration |
Off (D) |
| Read Only Diskette |
ON |
See > System Board Memory
for DIMM size, speed, and type.
Memory Table
DIMM sizes of 32, 64 and 128 MB are acceptable. DIMM height must not
exceed 2.5 inches. If SDRAM ECC and SDRAM (non parity) DIMMs are mixed, they will
configure as non-parity ECC. Install only SCDRAM ECC DIMMs to enable ECC.
Total System
Memory
(MB) |
DIMM
Bank-0
(MB) |
DIMM
Bank-1
(MB) |
DIMM
Bank-2
(MB) |
DIMM
Bank-3
(MB) |
| 32 |
32 |
- |
- |
- |
| 64 |
64 |
- |
- |
- |
| 64 |
32 |
32 |
- |
- |
| 96 |
32 |
32 |
32 |
- |
| 128 |
128 |
- |
- |
- |
| 128 |
64 |
64 |
- |
- |
| 256 |
128 |
128 |
- |
- |
| 256 |
128 |
64 |
64 |
- |
| 512 |
128 |
128 |
128 |
128 |
Back to 
Please see the LEGAL - Trademark notice.
Feel free - send a 
for any BUG on this page found - Thank you.