System / Processor - Board Locations (Netfinity 5500-M10 - Type 8661)

  Turn off the server, and disconnect the power cords before moving any jumpers.

System Board Component Locations

1 Processorboard connector (J19)
2 System management processor Error LED (CR24)
3 RAID channel 1 connector (J7)
4 RAID channel 1 Error LED (CR30)
5 RAID channel 2 Error LED (CR31)
6 Reserved (J54)
7 Reserved (J64)

8 Disable RAID Controller jumper block (J11)
Enable RAID controller (default) = Pin 1-2
Disable RAID controller = Pin 2-3

9 Reserved - Default = Pin 2-3 (J45)

10 Power on control jumper block (J32)
Default = Pin 1-2
Power on w/o control panel or System
Mgmt. Processor control = Pin 2-3

11 RAID download jumper block (J15)
Default = No jumper
Update RAID adapter EEPROM = Jumper

12 Reserved - Default = Pin 1-2 (J25)
13 Reserved - Default = Pin 1-2 (J9)
14 Power backplane cable connector (J8)
15 RAID channel 2 connector (to backplane) (J3)
16 RAID system Error LED (CR32)
17 Reserved (J34)
18 Reserved (J35)
19 SCSI activity LED connector (J52)
20 Reserved - Default = Pin 1-2 (J34)
21 Reserved - Default = Pin 1-2 (J29)
22 Reserved - Default = No jumper (J26)
23 IDE Connector (J33)

24 Disable Advanced System Mgmt Proc jumper block (J51)
Default = No jumper
Disable Advanced System Management
Processor = Jumper on J51

25 Fan connector (J36)
26 Diskette drive connector (J22)

27 Power on Password override jumper block (J24)

Changing the position bypasses the power-on
password check if the jumper has been moved
since the server was last powered on.

No need to move back afterwards.
Does not affect the Administrator password check.

28 Flash ROM page swap jumper block (J30)
Default = Pin 2-3
Changing the position of this jumper will
change which of the two pages of Flash ROM
is used when the system is started.

29 Controlpanel connector (J20)
30 Battery
31 Reserved (J46)
32 Hot-plug PCI pageswap jumper block (J53)
33 ISA expansion slot
34 Hot-plug switch connector (J16)
35 PCI slot LEDs (four are on this side of the board)
36 PCI slots 1-4 (hot-plug), Secondary PCI bus, bus 1
37 PCI slots 5 and 6, Primary PCI bus, bus 0

38 Parallelport connector (J56)
(Serial port A and B connectors are below
the parallelport connector)

39 Videoport connector (J2)
40 Management port C connector (J42)

41 USB 1 and USB 2 port connectors
(USB 2 is below USB1) (J31)

42 Mouse and Keyboard connectors (J1)
(The mouse connector is above the KBD connector)

43 Ethernet port connector (J4)
44 Reserved (J17)
45 Reserved (J18)

46 Disable Ethernet controller jumper block (J5)
Default = Pin 1-2
Disable Ethernet controller = Pin 2-3

47 Disable Video controller jumper block (J14)
Default = Pin 1-2
Disable Video controller = Pin 2-3

Processor Board Component Locations

1 Secondary microprocessor cache VRM connector (U15)
2 Secondary microprocessor cache VRM error LED (CR36)

3 Secondary microprocessor core VRM connector (U7)
4 Secondary microprocessor core VRM error LED (CR37)

5 Power control connector (J17)

6 Primary microprocessor cache VRM connector error LED (CR19)
7 Primary microprocessor core VRM error LED (CR17)

8 Power supply connector (J10)

9 Primary microprocessor cache VRM connector (U17)
10 Primary microprocessor core VRM connector (U22)

11 Microprocessor core-frequency-selection switchblock (SW1)

12 Reserved (J22)
13 Reserved (J20)
14 Reserved (J18)

15 System board connector (J9)
(on reverse side of processor board)

16 Primary microprocessor connector (U5)
17 Primary microprocessor error LED (CR12)

18 DIMM 1 error LED (CR8)
19 DIMM 2 error LED (CR9)
20 DIMM 3 error LED (CR10)
21 DIMM 4 error LED (CR11)

22 DIMM socket 4 (J1)
23 DIMM socket 3 (J2)
24 DIMM socket 2 (J3)
25 DIMM socket 1 (J4)

26 Secondary microprocessor error LED (CR13)
27 Secondary microprocessor connector (U6)

Processor Board Jumpers 

Jumper Name	Description
J22 - Reserved	The default position is no jumper on J22

Note:

1.  Turn off the server, and disconnect the power cords before moving any jumpers.
2.  Be sure the microprocessor bus-to-core ratio is set correctly.  For example, if you have a 400MHz microprocessor installed and the system bus speed is  100MHz (the default), be sure that the microprocessor core frequency selection switch  block is set to a bus-to-core ratio of 4 (400/100) see below table.

Core/Bus Ratio	SW1-1	SW1-2	SW1-3	SW1-4
4	On	On	On	Off
4.5	On	Off	On	Off
5	On	On	Off	Off

Memory-Module Kits

The server comes with a memory DIMM module installed on the processor board in connector J1.
The server supports a minimum of 128MB and a maximum of 2GB of system memory.
The memory-module sizes available for server 5500-M10 are 128MB, 256MB, and 512MB.

Install additional memory modules in connectors J2, J3, and J4, in that order.
If you mix DIMM sizes, install the largest sized DIMM in connector J1, the next large sized DIMM in connector J2, and so forth.

Install only 3.3V, 168-pin, 8-byte, registered DIMMs.
Only 100MHz, 72-bit, registered synchronous, error correcting code (ECC), x4 configuration DIMM memory is supported for the 128MB, 256MB, and 512MB DIMMs.

After install/remove any DIMM, you must save the new configuration information in the Configuration/Setup program. When you restart the server, the system displays a message indicating that the memory configuration has changed. Start the Configuration/Setup program and select Save Settings.

Please see the LEGAL  -  Trademark notice.
Feel free - send a   for any BUG on this page found - Thank you.