Aptiva 2137-SL A - System Board Connector and Functions
See > Memory Map - I/O Addresses
See > DMA / IRQ Assignments
Jumper/Settings Function
-------------------------------------------------------------
Please see the LEGAL - Trademark notice.
Connector
Function
Connected to..
CN1
Lower: PS/2 keyboard connector
Upper: PS/2 mouse connectorKeyboard
Mouse
CN2
Modem/voice-in connector
Modem card
CN3
Two Universal Serial Bus (USB) connectors
USB devices
CN4
Upper: Printer port
Lower: Serial port (COM1)
Video portPrinter
Serial device
Monitor
CN5
Upper: MIDI/game port
Lower: Line-out, line-in, mic-in portsJoystick
Speaker
Microphone
CN6
CD audio input connector
CD-ROM drive
CN8
ATI media connector (AMC)
Reserved
CN9
Modem ring-in wake-up connector
Modem card
CN10
Secondary IDE channel
CD-ROM drive
CN12
Hard Disk LED connector
Connect the
red wire to pin-1
white wire to pin-2
then leave pin-3, -4 as non connected
or connect
the red wire to pin-4
white wire to pin-3
then leave pin-1, -2 as non connected.Hard Disk Drive
CN13
Primary IDE channel
Hard Disk Drive
CN14
Power/suspend switch connector.
This connector has no directional concern.Power/suspend
switch
CN15
Standby power connector
Power supply
CN16
Diskette connector
Diskette drive
CN17
Power LED connector
Connect
green wire to pin-12
white wire to pin-14Power LED
CN19
System board power connector
Power supply
FN1
Processor fan connector
CPU heat sink
System Board Jumper Settings
Jumper/Settings
Function
JP9
1-2 (D)
2-3Password security
Check password
Bypass password
Processor Type Jumper Settings I
---------------------------------------------------------
JPX2 | IBM logo shown during POST
|
1-2 | is not shown during POST
2-3 | is shown during POST (D)
---------------------|-----------------------------------
System Board FRU P/N |
12J6890 or 12J6830 | Core/bus frequency rate
|
JPX3, JP4 | P54C 6X86L P55C/6X86MX/K6
|---------------------------------
2-3, (1-2, 4-5) | 1.5 3.0 3.5
2-3, (1-2, 5-6) | 2.0 2.0 2.0
2-3, (2-3, 5-6) | 2.5 --- 2.5
2-3, (2-3, 4-5) | 3.0 --- 3.0
|
System Board FRU P/N |
02K2550 or 02K2551 | Core/bus frequency rate
|
JPX3, JP4 | P54C 6X86L P55C/6X86MX/K6
|---------------------------------
2-3, (1-2, 4-5) | 1.5 3.0 3.5
2-3, (1-2, 5-6) | 2.0 2.0 2.0
2-3, (2-3, 5-6) | 2.5 --- 2.5
2-3, (2-3, 4-5) | 3.0 --- 3.0
1-2, (1-2, 5-6) | --- --- 4.0
1-2, (2-3, 5-6) | --- --- 4.5
---------------------------------------------------------
System Board FRU P/N |
12J6890 or 12J6830 |
|
JP3, JP5, JP6 | Processor core voltage
|
Closed, Open, 3-5 | 2.1V (reserved)
Closed, Open, 2-4 | 2.8V
Closed, Open, 4-6 | 2.9V
Closed, Open, 7-8 | 3.2V
Open, Closed, 1-3 | 3.3V
Open, Closed, 3-5 | 3.52V
|
System Board FRU P/N |
02K2550 or 02K2551 |
|
JP3, JP5, JP6 | Processor core voltage
|
Closed, Open, 3-5 | 2.2V
Closed, Open, 2-4 | 2.8V
Closed, Open, 4-6 | 2.9V
Closed, Open, 7-8 | 3.2V
Open, Closed, 1-3 | 3.3V
Open, Closed, 3-5 | 3.52V
---------------------------------------------------------
JP9 | Password security
1-2 | Check password (D)
2-3 | Bypass password
---------------------------------------------------------
JP10, JP11 | Host / PCI bus frequency
(1-3, 2-4),(1-3, 2-4)| 60/30 MHz
(3-5, 4-6),(1-3, 2-4)| 66/33 MHz
(1-3, 2-4),(3-5, 4-6)| 75/30 MHz
(3-5, 4-6),(3-5, 4-6)| 83/33 MHz
---------------------------------------------------------
NOTE: JPX3 in 12J6890 and 12J6830 is an
optional Jumper, the system board may come w/o it.
° System board FRU P/N 02K2551 comes with only 1MB video
memory and w/o cache memory.
° JP3 and JP5 is a 4-position Jumper block
Open = all jumpers removed
Closed = 4x jumper present (1-2, 3-4, 5-6, 7-8)
Processor Type Jumper Settings II
You must check out exact processor type before setting the processor type jumper.
The wrong processor type jumper setting may damage CPU, especially the single/dual voltage setting.
CPU | JP3 |JPX3| JP4 | JP5 |JP6| JP10 | JP11
-------------------------------------------------------------
Pentium®
-------------------------------------------------------------
P-166 |Open |2-3 |2-3, 5-6|Closed|1-3|3-4, 5-6|1-3, 2-4
-------|-------|----|--------|------|---|--------|-----------
P-200 |Open |2-3 |2-3, 4-5|Closed|1-3|3-4, 5-6|1-3, 2-4
-------------------------------------------------------------
Pentium® MMX
-------------------------------------------------------------
P-166 |Closed |2-3 |2-3, 5-6|Open |2-4|3-5, 4-6|1-3, 2-4
-------|-------|----|--------|------|---|--------|-----------
P-200 |Closed |2-3 |2-3, 4-5|Open |2-4|3-5, 4-6|1-3, 2-4
-------|-------|----|--------|------|---|--------|-----------
P-233 |Closed |2-3 |1-2, 4-5|Open |2-4|3-5, 4-6|1-3, 2-4
-------------------------------------------------------------
Cyrix / IBM 6x86L
-------------------------------------------------------------
PR-166+|Closed |2-3 |1-2, 5-6|Open |2-4|3-5, 4-6|1-3, 2-4
-------|-------|----|--------|------|---|--------|-----------
PR-200+|Closed |2-3 |1-2, 5-6|Open |2-4|1-3, 2-4|3-5, 4-6
-------------------------------------------------------------
Cyrix / IBM 6x86MX
-------------------------------------------------------------
PR-166+|Closed |2-3 |1-2, 5-6|Open |4-6|3-5, 4-6|1-3, 2-4
-------------------------------------------------------------
AMD K6
-------------------------------------------------------------
PR166 |Closed |2-3 |2-3, 5-6|Open |4-6|3-5, 4-6|1-3, 2-4
-------|-------|----|--------|------|---|--------|-----------
PR200 |Closed |2-3 |2-3, 4-5|Open |4-6|3-5, 4-6|1-3, 2-4
-------|-------|----|--------|------|---|--------|-----------
PR233 |Closed |2-3 |1-2, 4-5|Open |7-8|3-5, 4-6|1-3, 2-4
-------------------------------------------------------------
AMD K6 (only for system board FRU P/N 02K2550 and 02K2551)
-------------------------------------------------------------
PR266 |Closed |1-2 |1-2, 5-6|Open |3-5|3-5, 4-6|1-3, 2-4
-------|-------|----|--------|------|---|--------|-----------
PR300 |Closed |1-2 |2-3, 5-6|Open |3-5|3-5, 4-6|1-3, 2-4
-------------------------------------------------------------
NOTE: JPX3 in 12J6890 and 12J6830 is an
optional Jumper, the system board may come w/o it.
° System board FRU P/N 02K2551 comes with only 1MB video
memory and w/o cache memory.
° JP3 and JP5 is a 4-position Jumper block
Open = all jumpers removed
Closed = 4x jumper present (1-2, 3-4, 5-6, 7-8)
Refresh Rates and Monitor Frequencies
The following table lists the maximum vertical refresh rates supported by the
system's ATI 3D Rage II+ video controller.
The max. refresh rate set for each resolution
should be within the monitor's vertical frequency specifications. Refer to the service
manual provided with the monitor.
Color / Resolution
640x480
800x600
1024x768
256
100 Hz
100 Hz
100 Hz
64000
100 Hz
100 Hz
---
16000000
100 Hz
---
---
DIMM (Gold Contact) Configurations
DIMM 1
DIMM 2
Total Memory
8 MB
-
8 MB
16 MB
-
16 MB
32 MB
-
32 MB
-
8 MB
8 MB
-
16 MB
16 MB
-
32 MB
32 MB
8 MB
8 MB
16 MB
8 MB
16 MB
24 MB
8 MB
32 MB
40 MB
16 MB
8 MB
24 MB
16 MB
16 MB
32 MB
32 MB
8 MB
40 MB
16 MB
32 MB
48 MB
32 MB
16 MB
48 MB
32 MB
32 MB
64 MB
Back to
Feel free - send a for any BUG on this page found - Thank you.