SCSI - HD Jumper setting
For HDDs not found here, please visit:
URL > http://www.pc-disk.de < (appr. 5000 HDDs)
URL > http://www.storage.ibm.com/techsup/hddtech/hddtech.htm
SCSI Jumper Position SCSI Jumper Position
ID 1 2 3 ID 1 2 3
------------------------------------------------------
6 Off ON ON 2 Off ON Off
5 ON Off ON 1 ON Off Off
4 Off Off ON 0 Off Off Off
3 ON ON Off
---1---2---4--- Bit-Value ---1---2---4---
JP4 - On = No automatically spin up at power on.
Host system issues a start command to the drive.
JP5 - On = Unit attention after power on reset or SCSI Bus reset
is disabled
JP6 - On = the internal active SCSI terminator is enabled
JP7 - On = Target initiated synchr. negotiation is disabled, and
then the initiator is required to start negotiation
handshake if synchr. SCSI transfers are required.
JP12 can be used to drive a LED (8mA) pin-24 is +5V
JP8, JP9, JP10, and JP11 are not used
1 GB, 1.27 GB - SCSI (Series 300/700)
SCSI Position SCSI Position
ID A2 A1 A0 ID A2 A1 A0
------------------------------------------------------
7 - Reserved - 3 Off ON ON
6 ON ON Off 2 Off ON Off
5 ON Off ON 1 Off Off ON
4 ON Off Off 0 Off Off Off
---4---2---1--- Bit-Value ---4---2---1---
PK = Park (Placeholder for an extra jumper)
TE = Enable termination
1.12 GB, 2.25 GB - SCSI (Series 300/700)
SCSI Position SCSI Position
ID 4 3 2 1 ID 4 3 2 1
------------------------------------------------------
0 Off Off Off Off 8 Off Off Off ON
1 ON Off Off Off 9 ON Off Off ON
2 Off ON Off Off 10 Off ON Off ON
3 ON ON Off Off 11 ON ON Off ON
4 Off Off ON Off 12 Off Off ON ON
5 ON Off ON Off 13 ON Off ON ON
6 Off ON ON Off 14 Off ON ON ON
7 - Reserved - 15 ON ON ON ON
---1---2---4---8-- Bit-Value ---1---2---4---8--
See > more detailed jumper description
2 GB - SCSI (Series 300/700)
SCSI Position SCSI Position
ID 4 3 2 ID 4 3 2
------------------------------------------------------
6 Off ON ON 2 Off ON Off
5 ON Off ON 1 ON Off Off
4 Off Off ON 0 Off Off Off
3 ON ON Off
---1---2---4--- Bit-Value ---1---2---4---
2.1 GB, 4.5 GB - SCSI (Series 300/700)
SCSI Position SCSI Position
ID 4 3 2 1 ID 4 3 2 1
------------------------------------------------------
0 Off Off Off Off 8 Off Off Off ON
1 ON Off Off Off 9 ON Off Off ON
2 Off ON Off Off 10 Off ON Off ON
3 ON ON Off Off 11 ON ON Off ON
4 Off Off ON Off 12 Off Off ON ON
5 ON Off ON Off 13 ON Off ON ON
6 Off ON ON Off 14 Off ON ON ON
7 - Reserved - 15 ON ON ON ON
---1---2---4---8-- Bit-Value --1---2---4---8---
540MB, 720MB, 1GB and 2GB - SCSI-2 HDD-Jumper
The following SCSI-2 HDDs use jumpers to set the SCSI IDs, terminate the SCSI cabling chain, and
control the motor startup.
If a jumper is installed on the Bus Terminate jumper pins, the SCSI bus is terminated.
SCSI Position SCSI Position
ID 1 2 3 ID 1 2 3
------------------------------------------------------
6 Off ON ON 2 Off ON Off
5 ON Off ON 1 ON Off Off
4 Off Off ON 0 Off Off Off
3 ON ON Off
---1---2---4--- Bit-Value ---1---2---4---
IBM 0664 Model M1H & N1H 1.7MB - 2.0MB HDD-Jumper
Please see the LEGAL - Trademark notice.
Feel free - send a for any BUG on this page found - Thank you.