IBM-DOS V-7.0 -S- ERROR Messages

 Same parameter entered twice 
    Cause:    FORMAT.  You have entered one of the following parameters more than one time: /t, /n, /f, or /v.
    Action:  Re-enter the correct parameter.
 SDEFRAG: Not enough free disk space 
    Cause:    STACKER.  Stacker Optimizer needs xxxxx free bytes in the Stacvol file for Stacker drive x:.
    Action:  Remove some files and try again.
 SECOND diskette bad or incompatible 
    Cause:    DISKCOMP.  You tried to read from the wrong medium in an incompatible drive.
    Action:  Check your diskette by using the CHKDSK command.
 Sector not found 
    Cause:    The sector containing the data could not be located on the disk.
    Action:  Refer to the "Responses" section. If you get the same message, select Abort and rerun the command
              with a different disk.
 Sector size too large in file 
    Cause:    IBMBIO.  The device driver named in <filename> specifies a device sector size larger than the devices
              previously defined to DOS.
    Action:  Reduce the sector size to conform with the sector size of DOS.
 Seek error 
    Cause:    The hard disk or disk drive was unable to find the proper track on the disk.
    Action:
     o Make sure that the diskette is properly inserted in the drive.
     o Try a different drive.
     o Run CHKDSK.
     Refer to the "Responses" section.
 SHARE cannot be installed under PC DOSSHELL 
     Cause:    SHARE.  SHARE cannot be set up while operating under the PC DOS Shell.
     Action:  To set up SHARE, quit the PC DOS Shell; then, install SHARE from the command prompt, and start PC
               DOS Shell again.
 Sharing violation 
     Cause:    COMMANDS.  You tried to access a file using a sharing mode not allowed now.  Normally, this occurs
               when someone else is accessing the file compatibility mode for writing, or in a sharing mode that does not allow
               you to access the file at the same time.
     Action:  Wait a short time and try again.  If you need to respond, select "Retry" as your first choice.  If that
               fails, select "Abort."
 SMARTDrive configuration is too large 
     Cause:    SMARTDrive.  There is not enough memory for the configuration you specified.
     Action:  Check the amount of available extended memory your computer has by using the MEM /f or MEM /c
               command.  Adjust your configuration accordingly.
 SMARTDRV:  Double-buffering driver cannot be loaded into a UMB 
     Cause:    SMARTDRV.EXE.  An attempt to load SMARTDRV.EXE into an upper memory block failed.
     Action:  Check your CONFIG.SYS file and ensure that you are not attempting to load SMARTDRV.EXE using the
               DEVICEHIGH command or some other loadhigh utility.  Use the DEVICE= command only to load SMARTDRV.EXE.
 SMARTDRV:  There is not enough XMS memory to load SMARTDrive 
     Cause:    SMARTDRV.  Your system does not have enough memory available for SMARTDRV.  PC DOS will not load
               SMARTDrive.
     Action:  You must add memory to your system or reduce the amount of memory used by other TSRs.  Use the
               MEM /c command to view the amount of memory being used by other TSRs.
 SMARTDRV:  WARNING:  Unable to use disk cache on the specified drive 
     Cause:    SMARTDRV.  You have tried to use SMARTDRV on a CD-ROM, compressed drive, or network drive.
     Action:  Check the drive letter you specified for SMARTDRV and adjust accordingly.
 Socket Services not loaded 
     Cause:    PCMCIA.  An attempt was made to install Card Services without first having Socket Services loaded.
     Action:  Load Socket Services; then, install Card Services.
 Socket Services version must be 2.1 
     Cause:    PCMCIA.  The Socket Services Version on your system is not 2.1.
     Action:  Install Socket Services Version 2.1; then, install Card Services Version 2.1.
 Socket x: does not support DRVLOCK 
     Cause:    DRVLOCK.  The specified socket does not support the lock and unlock functions of DRVLOCK.
     Action:  Refer to the documentation that came with the socket to verify if it supports the DRVLOCK functions.
 Source and destination are the same 
     Cause:    MOVE.  You have specified the same drive for the source and target.
     Action:  Specify a different drive letter for the source and target drives.
 Source and target drives are the same 
     Cause:    RESTORE.  You have specified the same drive as the source and target.
     Action:  Specify a different drive letter for the source and target drives.
 Source destination conflict 
     Cause:    E.  The source and the target drives are the same.
     Action:  Do not specify the same drive for both the source and the target.
 SOURCE diskette bad or incompatible 
     Cause:    DISKCOPY.  The errors occurred while reading the diskette.  The error might have been caused by bad
               sectors, or the diskette in the source drive might not be compatible with the source drive type (a high-capacity
               diskette in a 360KB disk drive, for example).
     Action:  Check your diskette.
 Source does not contain backup files 
     Cause:    RESTORE.  The source medium does not contain files created by the BACKUP command.
     Action:  No action is required.
 Source path and target drive cannot be the same 
     Cause:    COMMANDS.  The specified source path and the destination drive are the same.
     Action:  Specify a path that is different from the destination drive.
 Source path required 
     Cause:    COMMANDS.  You did not specify a source path.
     Action:  Specify the path of the original file or directory.
 Stacker found an error while reading the FAT of the uncompressed drive 
     Cause:    DCONVERT, HCONVERT.  During the processing of these Stacker utilities, a problem involving the FAT of
               the uncompressed drive was discovered.
     Action:  Run CHKDSK /f.  Then rerun DCONVERT or HCONVERT.
 Stacker found an error while writing the FAT of the uncompressed drive 
     Cause:    DCONVERT, HCONVERT.  During the processing of these Stacker utilities, a problem involving the FAT of
               the uncompressed drive was discovered.
     Action:  Run CHKDSK /f.  Then rerun DCONVERT or HCONVERT.
 String not found 
     Cause:    E.  You specified a search for a character string that does not exist in the file.
     Action:  Specify another search string, or try searching for the string in another file that might contain it.
 Switch x is not valid 
     Cause:    DELTREE.  One or more of the switches entered for the command is not valid, is in the wrong order, or
               is duplicated.  This message might also occur if the command does not use a switch.
     Action:  Make sure that the character following the slash (/) is valid for the DELTREE command; then, try the
               command again.  For information about valid DELTREE command switches, see the DELTREE command or type
               deltree /? at the DOS command prompt.
 Syntax error 
     Cause:    DOS and COMMANDS.  The command format you typed is incorrect.
     Action:  Make sure that you have used the correct format for this command.  For information about the
               command, check the PC DOS 7 Command Reference or type at the DOS command prompt the name of the
               command followed by /?.
 SYS cannot operate on target drive 
     Cause:    SYS.  The target drive you specified is not supported by the SYS command.
     Action:  Specify a valid target drive.
 System resource exhausted 
     Cause:    COMMANDS.  The system is unable to obtain all needed resources to process this command.  All available
               storage is currently in use.
     Action:  Try one of the following:
     o Reduce the number of programs presently running on your system.
     o Edit the CONFIG.SYS file to reduce the value in the BUFFERS statement, or reduce the size allocated for a
       virtual disk. Restart the system and retry the command.
     o Install additional memory in your system.
     o Contact the supplier of the application.


Back to  Jump to TOP-of-PAGE

Please see the LEGAL  -  Trademark notice.
Feel free - send a Email-NOTE  for any BUG on this page found - Thank you.